行業資訊

濟南路面機械設備產生漏砂問題如何處理？

來源：http://m.3sj.org.cn/ 日期：2022-04-26

　　路面機械設備的使用環境通常都不是很好，因此使用期間要多注意一些事項，以及一些問題的出現，近來有用戶反映設備會出現漏砂現象，這要怎么處理呢？

　　The use environment of road machinery and equipment is usually not very good, so we should pay more attention to some matters during the use, as well as the emergence of some problems. Recently, some users reported that the equipment will appear sand leakage phenomenon, how to deal with it?

　　路面機械設備剛剛運行，就發生漏砂現象。檢查設備定向套開口有沒有正確安裝，開口角度為45°角正確；電機接線是否接反，運轉方向不對，正確轉向應該是由內向外轉動。

　　The phenomenon of sand leakage occurred when the road machinery equipment was just running. Check whether the opening of directional sleeve of equipment is correctly installed and the opening Angle is 45°。 Whether the motor wiring is connected in the wrong direction, the correct steering should be from inside to outside rotation.

　　路面機械設備漏砂面積大，但很均勻，類似于平攤在路面上。對除塵器進行檢查，可能是除塵器接線接反，導致除塵器不能正常工作；檢查設備的灰斗，是否長時間未清理，導致灰斗載滿，設備不能正常工作。

　　Road mechanical equipment sand leakage area is large, but very uniform, similar to flat spread on the road. Check the dust collector, it may be that the dust collector wiring is reversed, resulting in dust collector can not work normally; Check whether the ash hopper of the device has not been cleaned for a long time. As a result, the ash hopper is full and the device cannot work properly.

　　濟南路面機械設備兩側漏砂，展現為條狀。檢查料倉蓋是否蓋好，其次要檢查拋投，拋投的離地間隙是否過高，正常情況應當保持在1公分。除了上述情況以外，發生其他漏砂現象或者解決不了，應當檢查除塵器的通風口是否開啟。

　　Ji 'nan road machinery and equipment leakage sand on both sides, shown as strips. Check whether the bin cover is well covered, and then check the throw, throw the ground clearance is too high, the normal situation should be kept at 1 cm. In addition to the above situation, if other sand leakage phenomenon occurs or cannot be solved, check whether the vent of the dust collector is opened.

　　此外，如果說準備去購買路面機械設備，可以去看它的相關部件到底怎么樣，如果說部件比較優質，在實際應用的過程中效率也比較高的話是能夠滿足我們的要求，如果它的效率比較低，這個就不要考慮了。

　　In addition, if you want to buy road machinery equipment, you can go to see how its related parts are in the end, if the parts are relatively high quality and the efficiency is relatively high in the process of practical application, it can meet our requirements, if its efficiency is relatively low, this is not considered.

　　濟南路面機械設備產生漏砂問題如何處理？以上從三個方面來講解了問題，如果您要使用的更好，那就要平常中多去了解相關事項以及問題才行。更多內容就來網站m.3sj.org.cn咨詢吧！

　　Ji 'nan road machinery and equipment produced sand leakage problem how to deal with? The above explains the problem from three aspects, if you want to use better, it is necessary to learn more about the issues and problems in the ordinary. More content to the website m.3sj.org.cn consultation!

上一條：裝載機走合磨合期要注意什么細節？

下一條：濟南瀝青料在什么溫度下會發揮出好性能？